Read on to see what's new ...
|
V484/533 |
12.1 14.0 |
FIXED: |
Various small loader issues with the PC-DMIS BASIC loader. |
|
|
|
|
|
|
V483 |
12.1 13.0 14.0 |
FIXED: FIXED: FIXED: |
Reporting Defaults default colors incorrect. Colormap display sometimes causing the program display to be black. RCB Column settings not saved with the part.
|
|
|
|
|
|
|
V530 |
14.0 |
ENHANCEMENT |
Mouseclick productivity tools added. Videos on youtube Techtips. |
|
|
|
|
|
|
V482/529 |
12.1 14.0 |
FIXED |
new CMECAL2OPN, CMECAL2IMS, and CMEPPG2MOD configurations. |
|
|
|
|
|
|
V480/528 |
12.1 14.0 |
FIXED Enhancement Enhancement Enhancement |
Trim edge analysis sometimes results in a flipped edge vector. Edit a feature by double clicking it in the graphics area. Feature control frame column added to programming browser. Augment colormap progress bars with 1 of 5 for multiple results. |
|
V514 |
14.0 |
Enhancement |
24 bit color for PCM |
|
V480 |
14.0 |
FIXED |
/#sfo,plus (Hot + in-out of tolerance reporting entities) causes hard crash. |
|
|
|
|
|
|
V478 |
12.1 14.0 |
FIXED: FIXED: ENHANCEMENT: FIXED: |
CMEXPORT of ACIS doubles up all CheckMate Items. Change RCB default columns. CheckMate message area colored yellow if a command fails. cone measurement with one or two picks on conical face wonky. |
|
|
|
|
|
|
V477 |
12.1 14.0 |
FIXED: |
intermittent PCM crash associated with hybrid freeform/CMTRANS alignments. |
|
|
|
|
|
|
V476 |
12.1 14.0 |
FIXED: FIXED: |
PCM ascii loader takes too long to load when using the POI modifier. DMIS result loader missing some FA(label)[1,n] used for CAL output. |
|
|
|
|
|
|
V475 |
12.1 14.0 |
FIXED |
"Filter Facets for Point Cloud" option on the PCM defaults screen was not working. |
|
V475 |
12.1 14.0 |
ENHANCEMENT |
Added clip plane to PCM defaults screen to eliminate extraneous irrelevant data points. |
|
|
|
|
|
|
V474 |
12.1 14.0 |
ENHANCEMENT |
/#CMA,APT,LEFT,FIL100,GROUP to load every 100th point for CMTRANS work. |
|
V474 |
12.1 14.0 |
ENHANCEMENT |
/#COLMAP,LEFT to load the data with the color map loader. |
|
|
|
|
|
|
V473 |
12.1 14.0 |
FIXED |
Change color of hot entities not allowing selection from color pallette. |
|
V473 |
14.0 |
FIXED |
CM14 Assembly files only displaying segments in 'top' viewport. |
|
V473 |
14.0 |
FIXED |
Legend created from triangles instead of rectangles |
|
V473 |
14.0 |
FIXED |
Legend font not displayed correctly |
|
V473 |
14.0 |
FIXED |
Legend ratio of text vs colorbar is 25/75 (originally 50/50) |
|
|
|
|
|
|
V472 |
12.1 14.0 |
FIXED |
cmrename not remembering the last setting used on the 'explode' checkbox. |
|
V472 |
12.1 14.0 |
FIXED |
Constructed circles created from scans should use all PTS and not BF |
|
V472 |
12.1 14.0 |
FIXED |
Execute cminherit, make the required picks, hit ok {or enter) and SW shuts down every time. |
|
V472 |
14.0 |
ENHANCEMENT |
Added the ability to create/save a view(called a Layout). Added the ability to Layouts in the Model. In both part and assembly drawings. |
|
|
|
|
|
|
V471 |
12.1 14.0 |
FIXED |
2 point trim check with spacing not working |
|
V471 |
12.1 14.0 |
ENHANCEMENT |
CMTRANS scale limit increased from 10.0 to 100.0 |
|
V471 |
12.1 14.0 |
FIXED |
Constructed Cylinders having incorrect diameters. |
|
V470 |
12.1 14.0 |
ENHANCEMENT |
CMTRANS scaling supports values up to 100 now (was 10). |
|
V470 |
12.1 14.0 |
ENHANCEMENT |
Add ability to tolerance/report a GCURVE or GSURF or a group profile with true position with bonus from profile callout. |
|
V470 |
14.0 |
ENHANCEMENT |
CMTRANSing CAD is only an option in ASSEMBLY files. |
|
|
|
|
|
|
V469 |
12.1 14.0 |
FIXED |
constructed cylinders not being created in the correct orientation. |
|
V468 |
12.1 14.0 |
FIXED |
Datum reference switches not staying in select state after editing in edit picked. |
|
V468 |
12.1 14.0 |
FIXED |
CMMOVECOPYDELETE fixed in the modify menu. |
|
V468 |
14.0 |
ENHANCEMENT |
Ability to turn off Levels for a specific viewport on the ‘Levels’ tab. |
|
V468 |
14.0 |
ENHANCEMENT |
Ability to save and restore views on the ‘Levels’ tab. |
|
V468 |
12.1 14.0 |
FIXED |
CMSIMULATION fixed in verify menu. |
|
V467 |
12.1 14.0 |
|
Parallelism label not showing up in CheckMate Labels. |
|
V466 |
12.1 14.0 |
FIXED |
Trim check probe moves not in the correct location when approach/retract dually fields are being used. |
|
V465 |
12.1 14.0 |
ENHANCEMENT |
Enhance Geopak 2100 results loader for Equator authoring. |
|
V464 |
12.1 14.0 |
ENHANCEMENT |
support of PC-DMIS VBA translations. |
|
V464 |
12.1 14.0 |
FIXED |
MLB to DMIS. Incorrect output like TRANS/ZORIG,DAT(PLANE1) has now been corrected to TRANS/ZORIG,FA(PLANE1). |
|
V462 |
12.1 14.0 |
ENHANCEMENT |
ADDED raw point output for GEOPAK2100. |
|
V462 |
12.1 14.0 |
FIXED |
cmswap work not working on individual points on multipoint measurement. |
|
V461 |
12.1 14.0 |
FIXED |
CMSFQ report area empty. |
|
V461 |
12.1 14.0 |
FIXED |
Rotate copy (CME) was interpreting angle as radians instead of degrees. |
|
V460 |
12.1 14.0 |
FIXED |
Rotate copy was causing system to crash. |
|
V460 |
12.1 14.0 |
FIXED |
NETWORKING-reconnection attempt not looking for the right key number. |
|
V460 |
12.1 14.0 |
FIXED |
NETWORKING-grace period for reconnection set to 0. |
|
V460 |
12.1 14.0 |
ENHANCEMENT |
CMMULTCYLNI and CMMULTCYLNO for measuring multicylinders added. |
|
v459 |
12.1 14.0 |
ENHANCEMENT |
On CMEXPORTDLG, added a switch for the in/out of tol summary box. |
|
v459 |
12.1 14.0 |
FIXED |
the level list updates on /SETA,LEV if you add a new level. |
|
V458 |
12.1 14.0 |
FIXED |
Cannot measure slot inners with a single edge pick. |
|
V457 |
14 |
ENHANCEMENT |
convert a feature measurement to a construction. |
|
V457 |
14 |
ENHANCEMENT |
replace a feature without having to recreate all the other features that get referenced to it. |
|
V456/506 |
14 |
ENHANCEMENT |
/SETA,COL and /SETA,LEV can be used to set default colour and level for new entities that use the default color and layer (APTIN groups, model.fct "colormap" etc.). The default default color is now grey instead of black. |
|
V456/506 |
14 |
ENHANCEMENT |
CMTRANS will work with SOLIDWORKS solids in assembly space (still work to do for part space). Choose either "All" to move the solid and CheckMate entities together "All non-cm" to move just the solid. |
|
V456/506 |
14 |
FIXED |
In 506 the colormap stuff is now complete. You should find 506 part files to be much smaller and much faster than 456 part files. |
|
V456/506 |
14 |
|
NOTE : If you have a part file with CheckMate data, you can now save it as an assembly and have all the CheckMate data go across (be sure to save the part file just before the conversion). Also, a similar technique is used to make it that if the CheckMate add in is started after a part is loaded, the CM data now comes alive. |
|
V455 |
12.1 14.0 |
FIXED |
On Ouptut Program screen, recall Initial CS field being stuck at SOFTOR. |
|
v452 |
14 |
FIXED |
Importing CheckMate12.1 import files showing ??? on constructions. |
|
V451 |
12.1 14.0 |
FIXED |
at least 4 point are output for a scan mode line measurement (Equator may filter out first and last so if only 2 or 3 points were measured the line measurement might fail with "too few points" error. |
|
V450 |
12.1 14.0 |
ENHANCEMENT |
reworked the datum offset code. Instead of setting a zero on the datum it offsets only by the datum's deviation. This way all moves and measurements regardless of which axis system they're in should be nominally the same, i.e. no out of volume issues. |
|
V449 |
12.1 14.0 |
FIXED |
DMIS output for distance between the first point on a multi-point surface measurement was coming out in touch point style: OUTPUT/FA(PN001),FA(SP00201). When the surface measurement is converted to scan mode this now comes out as: CONST/POINT,F(W0001),TR,FA(SP002)[1] and OUTPUT/FA(PN001),FA(W0001) |
|
V448 |
12.1 14.0 |
FIXED |
DMIS output for projecting a best -fit circle to a plane coming out as CONST/BF...PROJCT instead of CONST/CIRCLE...PROJCT |
|
V447 |
12.1 14.0 |
FIXED |
CMAUGREMOVE breaking construction/coordinate system references |
|
V447 |
CM14 |
FIXED |
single pick circle inner/outer, cylinders etc.. not being placed on CAD when the pick is accidentally the face and not the edge. |
|
V447 |
12.1 14.0 |
ENHANCEMENT |
Added a switch to autosection screen to put each section in its own segment. |
|
V447 |
12.1 14.0 |
ENHANCEMENT |
Implemented cmrib/cmthick into cm14. |
|
V447 |
12.1 14.0 |
ENHANCEMENT |
Added option to Extract point from scan for a constructed point. |
|
V447 |
12.1 14.0 |
ENHANCEMENT |
HAVE SIMULATION BASED ON PROBE TIP SIZE OF PROBE, NOT THE ATTRIBUTE ON THE MEASUREMENT. |
|
V445 |
12.1 14.0 |
FIXED |
Reporting Browser unable to show results in a 'fitted' state. |
|
V445 |
12.1 14.0 |
FIXED |
Tolerancing Perpendicularity rep ent in CheckMate does not go out to the EXCEL_OUT.csv for excel reports. |
|
V442 |
12.1 14.0 |
FIXED |
Importing DMO file and three measurement's rep ents looks mis -vector'd. |
|
V440 |
12.1 14.0 |
FIXED |
Checkmate not generating Angularity code correctly for MLB output. |
|
V439 |
14 |
FIXED |
can't cancel out of 'put hot on action line' command popups -cmhot2al. |
|
V439 |
14 |
ENHANCEMENT |
set the number of decimal replaces in the CMM report on the CheckMate Output screen for DMIS. |
|
V439 |
14 |
FIXED |
right clicking to use select from segment, leaves the segment name highlighted and shouldn't. |
|
V439 |
14 |
FIXED |
Auto probe Clearance moves do not work. |
|
V439 |
14 |
FIXED |
Relative probe move with a surface measurement doesn't work. (execute probe move then pick surface measurement) |
|
V439 |
14 |
FIXED |
when measuring multiple circle inners at once, the first one is ok. The rest are rotated 90 degrees out of axis. |
|
V439 |
14 |
FIXED |
cannot copy/move/drag cylinder inner measurement to another segment. |
|
V439 |
14 |
FIXED |
Having trouble creating constructed cylinders. |
|
V439 |
14 |
FIXED |
addin selection and deselect ckmt -sw SolidWorks crashes. |
|
V438 |
14 |
ENHANCEMENT |
Add PCM commands to CM14 menus and Ribbon. |
|
V438 |
14 |
ENHANCEMENT |
Add hot+/- commands to CM14 menus and Ribbon. |
|
V438 |
14 |
ENHANCEMENT |
Add "Inherit Tolerance/Probe Attribute" to the Modify Ribbon. |
|
V438 |
14 |
ENHANCEMENT |
Implement Hot+/- BOX,BAND,FENCE commands. |
|
V433 |
12.1 14.0 |
FIXED |
pos-length is loading into Checkmate as zeros which is not what is in the LK cmm report. |
|
V429 |
14 |
FIXED |
reporting flag colors not being generated correctly. |
|
V428 |
14 |
FIXED |
Feature names in constructions turn to "????" in the programming browser after loading a second probe. |
|
V425 |
12.1 14.0 |
FIXED |
Circular Runout results from the equator not importing into CheckMate. |
|
V425 |
12.1 14.0 |
ENHANCEMENT |
When selecting Renishaw Modus for Equator on the checkmate output screen, also automatically generate a CAL file. |
|
V424 |
14 |
FIXED |
Automatic Surface Compare not working. |
|
V423 |
14 |
FIXED |
mysterious hot groups created when saving files. |
|
V422 |
12.1 14.0 |
FIXED |
after editing cylinder depths, the graphic does not update to the new values and neither does the simulation. |
|
V419 |
12.1 14.0 |
FIXED |
problems loading in CAD STP files from Chrysler. |
|
V418 |
14 |
FIXED |
I have a file with no CAD, just segments, whiskers, repents and cannot fit the view to the window. |
|
V415 |
14 |
FIXED |
level tab does not update properly when switching between multiple open files. |
|
V413 |
14 |
FIXED |
Edited a probe to delete some existing positions. Positions would not delete. |
|
V409 |
14 |
FIXED |
Pressing the excel defaults toolbar button causes hard crash. |